@ameera

ameera

Si Hebat

Jarak kota A-B di peta X adalah 25 cm, selisih garis lintangnya 90 detik. Dengan keterangan di atas, skala peta X adalah? a. 1: 16.550.000 b. 1: 1.655 c. 1: 662.000 d. 1: 662
Answer
Proses pelapukan dan pembentukan tanah yg umum terjadi di indonesia adalah pelapukan? a. fisika b.kimiawi c. organis d. mekanik sebutkan alasannya!
Answer
Soalnya ada di gambar
Answer
Gambarlah grafik yang melaluI titik w(6,4) dan tegak lurus garis de dengan d(0,2) dan e(5,0)
Answer
Cuando comenzó y terminó la edad antigua?
Answer
Bantuin ya.. di pepak aku ngga adaKraton Majapahit ngirim ... bola kanggo nggemput musuh
Answer
Bantuin ya.. di pepak aku ngga adaKabeh uba ... wis di sapae kanggo penghargyan mengeti dina kamadikan
Answer
Bantuin ya.. di pepak aku ngga adaPemerintah ngreka ... , amrih rakyate urip santosa
Answer
Apa yang dimaksud kohesi dan transisi?Cara menentukan kalimat simplek yang benar?
Answer
Nama gelar orang yang bekerja keras dan ulet berjasa terhadap masyarakatnya ?
Answer
Apa hasil hasil positif setelah pembangunan nasional ?
Answer
Apa hakikat perjuangan proklamasi kemerdekaan 17 Agustus 1945?hakikat itu gimana sih maksudnya?
Answer
Tentukan jumlah semua bil positif 4 digit dengan tidak ada angka 0 !Tolong ya, beserta caranya :D
Answer
Fungsi desoldering pump?
Answer
Cara memasang rangkaian'' PCB dan melepaskan rangkaian'' nya?
Answer
Apa guna pcb? .......................................
Answer
Ini namanya apa? lihat di file ya.. , yg di bunder merah, gampang kok :-) cuma 1
Answer
Tolong artiin ya ^_^ , pakai google translate? langsung ane laporin :3 ADD THE POWER SWITCH The last piece of preparatory bodywork is adding the power switch, a large toggle placed rear topside so it looks like a tail. Find an appropriate mouse-tail location, then drill a hole in the case big enough for the switch. If the switch has a threaded bushing and two nuts, take one nut off, insert the bushing up through the hole, and then tighten the nut back down onto the outside of the case. In some cases, a plastic screw post interferes with the tail area. If so, you can cut out the post and reconnect the top and bottom halves with tape or glue.MOTOR AND BATTERY PLACEMENT Now we’re ready to figure out the arrange- ment of the bigger components and cut openings for the motors. Mouse shapes vary, so you’ll use some judgment here, but the two motors should be oriented perpendicular to the centerline of the body, so the bot travels in a straight line. Also be sure to leave enough space behind the motors for the battery.Once you’ve placed the motors and battery, you’re ready to cut openings for the axles and wheels, which are simply the drive shafts and gears of the motors.You’ll want to angle the shafts coming out of the mouse body so they support the bot and set a proper speed. The steeper the angle, the less rubber will meet the road, which slows the bot down − but this is good, since many builders have complained that Mousey moves too fast. If you’re using the lively Solarbotics RM1 motors, 60 degrees is about right, as shownMotor placement, angle, and switch placement are very important for making Mousey work properly.Use poster putty to hold the motors in place tempo- rarily. Then get down at eye level and make sure the gear “wheels” are making good, level contact with the table. Once the motors are positioned properly, glue them in place.
Answer
Artiin ya ^_^MOUSEY’S CIRCUITRY IS FREEFORMED This means that we’ll solder the parts to each other without a circuit board, building everything up right inside the mouse case. But before we do this, we’ll need to prep the case and install the motors, and then breadboard the circuitry separately to make sure everything works.Before unholstering your Dremel tool, you’ll need to determine if the mouse has enough space inside. Unscrew the mouse case and eyeball it to make sure that it will hold the two DC motors and a 9-volt battery. Screws may be hiding under little nylon feet or tape strips on the bottom of the mouse. Save these bits so you can put them back at the end of the build; they’ll help reduce friction. PERFORM AN ALIEN MOUSE AUTOPSY Once you have a suitable candidate, remove all of the mechanics and electronics. Unhook the mouse cable from its plug-type connector, pop out the scroll wheel (if it has one), and then pry out the PCB (printed circuit board). Set these parts aside. Then use your Dremel and cut-off wheel to hollow out the case, removing all of the plastic mounts and partitions inside, except for any screw post(s) that hold the case together. Do the same for the top half, although you may want to leave the mounts that hold the buttons in place. Note: Plastic dust is nasty stuff, so work on news- paper and wear goggles and a mask.
Answer
Tolong dikrama aluskan ;-)''bu sati, es doger ini terbuat dari apa?'''''apa komponen/ bagian yang membuat enak?''''kira-kira berapa menit membuat es doger?''apa yang harus paling diperhatikaan saat membuat es ini?'''' es doger itu asalnya dari mana?'''' awalnya, siapa yg membuat es ini?'''' apa arti es doger?'''' bagaimana tips ibu sati agar es doger ini enak?''yang njawabnya lengkap aku kasih jawaban yg terbaik, JANJI :)
Answer
Untuk tugas sekolah nih, phunsukhwang.blogspot.comblog saya kurang apa ya?termasuknya di kamu loading blogku lambat/cepat ?saran dan kritik?
Answer
Buatlah 1 contoh soal yang berhubungan dengan teorema Vieta dan cara penyelesaiannya ! bantuin yaa..
Answer
Tentukan koordinat bayangan titik berkut ini:a.P(4,7) dicerminkan terhadap garis x = 5b.Q(2,-3) dicerminkan terhadap garis x = -4beserta cara yaaa..
Answer
Jelaskan tiap panambang itu cara menulisnya gimana dan kalau bisa dikasih contohnya yaa :D- panambang -i- panambang -ake- panambang -e lan -ne- panambang -a- panambang -ana- panambang -en- panambang -natolong ya besok UTS nih ^_^, yang jawabannya mantap aku kasih bintang 5 ! :D
Answer

Life Enjoy

" Life is not a problem to be solved but a reality to be experienced! "

Get in touch

Social

© Copyright 2013 - 2024 KUDO.TIPS - All rights reserved.