Tolong artiin ya ^_^ , pakai google translate? langsung ane laporin :3
ADD THE POWER SWITCH
The last piece of preparatory bodywork is adding the power switch, a large toggle placed rear topside so it looks like a tail. Find an appropriate mouse-tail location, then drill a hole in the case big enough for the switch. If the switch has a threaded bushing and two nuts, take one nut off, insert the bushing up through the hole, and then tighten the nut back down onto the outside of the case. In some cases, a plastic screw post interferes with the tail area. If so, you can cut out the post and reconnect the top and bottom halves with tape or glue.
MOTOR AND BATTERY PLACEMENT
Now we’re ready to figure out the arrange- ment of the bigger components and cut openings for the motors. Mouse shapes vary, so you’ll use some judgment here, but the two motors should be oriented perpendicular to the centerline of the body, so the bot travels in a straight line. Also be sure to leave enough space behind the motors for the battery.Once you’ve placed the motors and battery, you’re ready to cut openings for the axles and wheels, which are simply the drive shafts and gears of the motors.You’ll want to angle the shafts coming out of the mouse body so they support the bot and set a proper speed. The steeper the angle, the less rubber will meet the road, which slows the bot down − but this is good, since many builders have complained that Mousey moves too fast. If you’re using the lively Solarbotics RM1 motors, 60 degrees is about right, as shown
Motor placement, angle, and switch placement are very important for making Mousey work properly.Use poster putty to hold the motors in place tempo- rarily. Then get down at eye level and make sure the gear “wheels” are making good, level contact with the table. Once the motors are positioned properly, glue them in place.
ADD THE POWER SWITCH
The last piece of preparatory bodywork is adding the power switch, a large toggle placed rear topside so it looks like a tail. Find an appropriate mouse-tail location, then drill a hole in the case big enough for the switch. If the switch has a threaded bushing and two nuts, take one nut off, insert the bushing up through the hole, and then tighten the nut back down onto the outside of the case. In some cases, a plastic screw post interferes with the tail area. If so, you can cut out the post and reconnect the top and bottom halves with tape or glue.
MOTOR AND BATTERY PLACEMENT
Now we’re ready to figure out the arrange- ment of the bigger components and cut openings for the motors. Mouse shapes vary, so you’ll use some judgment here, but the two motors should be oriented perpendicular to the centerline of the body, so the bot travels in a straight line. Also be sure to leave enough space behind the motors for the battery.Once you’ve placed the motors and battery, you’re ready to cut openings for the axles and wheels, which are simply the drive shafts and gears of the motors.You’ll want to angle the shafts coming out of the mouse body so they support the bot and set a proper speed. The steeper the angle, the less rubber will meet the road, which slows the bot down − but this is good, since many builders have complained that Mousey moves too fast. If you’re using the lively Solarbotics RM1 motors, 60 degrees is about right, as shown
Motor placement, angle, and switch placement are very important for making Mousey work properly.Use poster putty to hold the motors in place tempo- rarily. Then get down at eye level and make sure the gear “wheels” are making good, level contact with the table. Once the motors are positioned properly, glue them in place.
bagian terakhir dalam persiapan bagian mesin itu dengan menambahkan daya saklar, pengubahan besar ditempatkan di belakang dek atas jadi kayak/seperti ekor.mencari sebuah ketepatan lokasinya ekor-tikus,lalu lubangi/di bor sebuah lubang di dalam kotak/tempat besar/yang cukup untuk saklarnya. kalo/jika saklarnya mempunyai lapisan ber ulir/ada alurnya dan dua kacang/mur,ambil satu mur ke atas lewat lubangnya,dan kemudian rekatkat/dikencangkan dibawah belakang sampai didepan kotaknya. di beberapa kotak/wadah, sebuah sekrup dari plastik menggabung sama/dengan area ekor/kabel .jika begitu,kamu bisa memotong kabel utama dan gabung kembali atas dan bawah setengahnya dengan lem atau solasi.
pelatakan motor dan baterai
sekarang, kita siap untuk gambaran tentang susunan componen yang lebih besar dan memotong pembukaan/bukaan pada motor. Dengan bentuk berbeda,kamu bisa menggunakan beberapa keputusan sisini,tapi bot motor harus berorientasi tegak lurus ke garis tengah badan. Jadi kedua motornya perjalanannya dalam garis lurus.juga harus dipstikan untuk memberi sedikit ruang cukup dibelakang motor untuk bterainya.sesekali kamu taruh/letakkan motor sama baterai,kamu harus siap memotong pembukanya untuk sumbu roda sama rodanya,dimana mudah digerakkan poros sama rantai ke motornya.kamu akan menginginkan sudut poros datang ke badan utama jadi mereka/motornya mendukung botnya dan menyetel kecepatan yang pas. Sudut yang lebih miring/curam, karet yang sedikit ada akan bertemu dengan jalur,dimana memperlambatin botnya ke bawah,tapi ini bagus,sejak banyak pembangun komponen ,ulai menurun kinerjanya karena rangkaian tadi bergerak terlalu cepat.jika kamu mengguanakan motor RM1 Solarbotics yang menyala,dengan sudut 60 derajt ke kanan,seperti contohnya/gambar yang dilihatkan.
Peletakan motor,sudut,dan peletakan saklar sanagt penting untuk membuat alat mousey bergerak sempurna.gunakan pelekat dempul untuk menahan motornya di tempat dalam tempo bergiliran.terus dapatkan atau letakkan kebawah di level mata dan pastikan rantai “roda”nya telah dibuat bagus,kontak tingkatan dengan meja. Sesekali/supaya motornya terletak pas. lem alatnya di tempatnya
Semoga membantu,klik jawaban terbaik yaa,capek mataku liat kamus buku lagi...